what to put on cornhole board before applying decal

Decals are a quick and piece of cake alternative to painting cornhole boards. However, if yous take never applied decals before, this job can seem daunting. But don't fret: nosotros'll bear witness you how to apply cornhole decals perfectly each and every time.

Choose a Method: Wet or Dry

There are two general methods for applying cornhole decals: wet or dry. The method you choose will depend on the blazon of decal you wish to apply and your experience with decal application.

Moisture and dry out applications are very similar except wet application uses a bit of water in the process, equally the proper name implies. Remember that decals should only be applied to clean surfaces for best results.

Method 1: Wet Application

Generally speaking, wet application is better for first-timers because it is more forgiving, allowing yous to slide the decal around a chip earlier making the final placement. Hither's how to apply cornhole decals with the wet method:

• Decals should merely be applied to clean surfaces. Wipe downwards your boards to remove any debris.
• Before applying your decal, exist sure to mensurate and re-measure its placement. Marking your lath lightly with a wax or graphite pencil can help y'all go on the decal on target when you begin the application process.
• Once you are comfy with your decal'due south placement and have marked guidelines on your board, lightly mist the board with a solution of one drop of dish soap per 12 ounces of h2o.
• Skin off the bankroll tape of your decal and mist the back of the decal too.
• Place the decal on your lath according to the guidelines y'all fabricated, starting from ane border and slowly laying down the rest of the decal. You lot should exist able to slide the decal slightly if you miss your marks.
• Employ a credit card or squeegee to smoothen out the surface of the decal. This volition help yous massage out those pesky air bubbling that are a seemingly unavoidable part of decal awarding.

Method Two: Dry out Application

The dry application procedure is a niggling less forgiving than the moisture application procedure because once the decal touches your board it is pretty much stuck. For dry application, your board and decal demand to be clean and dry. To apply decals with the dry method:

• Measure and re-measure your decal'due south placement. Wax or graphite pencils are great for making light marks to serve as guidelines for your decal's placement.
• Once you are satisfied with your decal's placement, record one border of the decal, preferably a straight edge, to the board while the decal's backing sheet is still in place. This tape volition serve as a hinge to assistance keep your decal aligned during awarding. Painter'south tape works all-time for this because it harms neither your board nor your decal.
• Flip the decal over so that the backing sheet is facing up.
• Brainstorm to remove the backing canvas, starting at the swivel and peeling off virtually an inch of the backing canvass.
• Place the now-exposed part of your decal on the lath, starting at the swivel and within the guidelines you made in footstep one.
• Go on to peel off the backing tape, inch by inch. Take your fourth dimension with this step to ensure that yous are staying inside your guidelines. Use a credit card or squeegee to smooth out the decal as yous go.

Air Bubble Removal

Whichever method you choose, chances are you will have to deal with air bubbles in your decal design. This is an nearly unavoidable function of the application process. Thankfully, these bubbling are removable. Here are some tips to help with bursting those pesky bubbles:

• Utilize gentle strokes with a credit card or squeegee to ensure that your decal goes on as smoothly as possible the first time.
• Starting from the eye of the decal, use your credit card or squeegee to push out bubbles once the decal is already applied.
• For bubbles that simply won't go away, you can use a small pin to poke a pigsty in the chimera. The hole only needs to be large plenty for air to escape, and one time the chimera is deflated the pigsty will not exist visible. One time you create a pigsty, you tin push air out of the bubble starting from the farthest edge of the bubble and working your way toward the pigsty.
• Smaller bubbles tend to deflate on their own over time. Allow your boards to sit for a day after you lot utilise cornhole decals. This will let smaller bubbles to disappear on their own.

Protecting Your Decal

Once you have removed the air bubbles, let your cornhole board decal to dry for a day (especially if you utilize the moisture method). If you lot are in a hurry, you tin apply a hairdryer on low rut to assist the decal set more than rapidly.

Once your decal is dry, you'll desire to apply a polyurethane clear coat to protect your decal from clothing-and-tear. Nosotros have an all-inclusive weblog mail on the topic of caring for cornhole boards. You'll want to check that out before applying the poly.

Cornhole board designs vary greatly, and decals are a great way to customize your set. From sporting teams to college cornhole boards, decals permit you to bear witness your allegiance when playing your favorite game. Nosotros have a great option of cornhole decals; be sure to check them out.

Shop Our Cornhole Decals

lilienthallogetch39.blogspot.com

Source: https://customcorntoss.com/apply-cornhole-decals

Share this post